How to Obtain Huawei B315s-936 (Globe) Admin Access:
1) Enter USB mode by following Step 3 of “HUAWEI B315S-936 UNLOCKING Step by Step”.
2) Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read IMEI”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes . You might brick your modem (Joke lang).
3) Enter the following commands:
First Code: This Query Datalock Status Value. Default value is “1” (Enabled)
at^datalock?
Second Code: This Sets The Datalock Value to 12345678
AT ^ NVWREX = 50502,0,128,4A FB 2D 5A 34 74 86 F0 A6 CC AE 46 99 53 83 1D 5C B1 7E 2A EF B2 B0 1A EF 53 03 8E C8 FF 1C 0D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8B 8C F4 B5 AF 0C F2 2C FE E0 F4 46 9C CF 47 95 36 71 1F 1C BF 05 7F 84 AB A9 F2 92 89 33 3C 01 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Third Code: This Sets Datalock Status value to “0” (Disabled)
at^datalock="12345678"
Fourth Code: This will set your modem to factory mode
at^sfm=1
Fifth Code: This will reset your modem. Wait until the modem reboots and shows a
AT^reset
---Steady power light indicator Only !!
4) Connect your modem to your PC via LAN Cable
Under “Network Properties”, Set IP manually as follows:
click “Use the Following IP Address”
IP address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
Tick “Use the following DNS Server Adressess”
Preferred DNS: 192.168.1.1
Alternate DNS: (leave blank)
Click OK
5) Run “Config Updater” login kayo user user pero minsan kahit wala start nyo lang and wait for it to complete successfully.
Exit “Config Updater” and reboot modem.
6) Enter USB mode (back to Step 1 USB Mode link)
• Run CID reader in USB mode and enter the following commands:
Pag ayaw mag telnet kayo 192.168.1.1 duon nyo input yan..
Telnet 192.168.1.1
user:admin
pas:admin or
user:user
password:user
First Code : This command will kick your modem out of factory mode
at^sfm=0
Second Code : Resets and reboots the modem
AT^reset
7) After successfully rebooting, go to Network Properties again and click “Obtain IP
Address Automatically” and “Obtain DNS Address Automatically”. Try to log into the
modem’s web interface by typing 192.168.254.254 in your browser.
Login as....
Username: admin
Password: admin
Go to “Settings”.
Choose “Restore Default”
The modem will reboot.
Done. You now have admin access to your modem.
pag ayaw mag hardreset po kayo ulitin nyo :p
WALANG KWENTA ADMIN!! Kulang TABs!! parang User lang And DAMOT ni Globe!! walang APN setting
Dahil Walang kwenta yung admin mag CID Reader nalang tayo wahaha or Mobile Partner pwede din mag set ng APN or 3G Only parasa RED LIGHT na SMART sakit ni 315s 4G REDLIGHT....
Set the APN to “internet.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Postpaid/LTE)
Enter this command:
AT+CGDCONT=1,"IP","internet.globe.com.ph"
OR Set the APN to “http.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Prepaid/LTE)
Enter this command:
AT+CGDCONT=1,"IP","http.globe.com.ph”
OR Set the APN to “internet” of the Smart Network to be connected to (use if sim is Smart Prepaid/LTE).
Enter this command:
AT+CGDCONT=1,"IP","internet”
Last command Reboots the modem.
AT^reset
Eto ibig sabihin ng format ng command
AT+CGDCONT=1,"IP","http.globe.com.ph"
ATD*99***1#
red = profile priority
green = IP address ex:format (xx.xx.xx.xx)
blue = APN name
pink = dialup number (optional kung 3g ang masagap na signal) source (Freddy3k)
MOBILE PARTNER USB MODE
No Signal if naka Lock sa LTE Only
Gawin mo AUTO yan mag kakasignal na yan
Paano Gawin Pumunta sa Setting Preferences
UPDATE FULL ADMIN DE-BRAND
Pag nasa Step 4 kayo sa itaas pwede nyo diretso debrand na yan
Procedure ay galing dito http://www.symbianize.com/showthread.php?t=1341870
1) Enter USB mode by following Step 3 of “HUAWEI B315S-936 UNLOCKING Step by Step”.
2) Run CID reader in USB mode and enter the following commands.
Note: select proper COM port in your CID reader before entering the codes below. To check if you have chosen the right COM Port, click on “Read IMEI”. The “Logs” window should display the modem’s IMEI number otherwise select a different COM Port. Do not edit the codes . You might brick your modem (Joke lang).
3) Enter the following commands:
First Code: This Query Datalock Status Value. Default value is “1” (Enabled)
at^datalock?
Second Code: This Sets The Datalock Value to 12345678
AT ^ NVWREX = 50502,0,128,4A FB 2D 5A 34 74 86 F0 A6 CC AE 46 99 53 83 1D 5C B1 7E 2A EF B2 B0 1A EF 53 03 8E C8 FF 1C 0D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8B 8C F4 B5 AF 0C F2 2C FE E0 F4 46 9C CF 47 95 36 71 1F 1C BF 05 7F 84 AB A9 F2 92 89 33 3C 01 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Third Code: This Sets Datalock Status value to “0” (Disabled)
at^datalock="12345678"
Fourth Code: This will set your modem to factory mode
at^sfm=1
Fifth Code: This will reset your modem. Wait until the modem reboots and shows a
AT^reset
---Steady power light indicator Only !!
4) Connect your modem to your PC via LAN Cable
Under “Network Properties”, Set IP manually as follows:
click “Use the Following IP Address”
IP address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
Tick “Use the following DNS Server Adressess”
Preferred DNS: 192.168.1.1
Alternate DNS: (leave blank)
Click OK
5) Run “Config Updater” login kayo user user pero minsan kahit wala start nyo lang and wait for it to complete successfully.
Exit “Config Updater” and reboot modem.
6) Enter USB mode (back to Step 1 USB Mode link)
• Run CID reader in USB mode and enter the following commands:
Pag ayaw mag telnet kayo 192.168.1.1 duon nyo input yan..
Telnet 192.168.1.1
user:admin
pas:admin or
user:user
password:user
First Code : This command will kick your modem out of factory mode
at^sfm=0
Second Code : Resets and reboots the modem
AT^reset
7) After successfully rebooting, go to Network Properties again and click “Obtain IP
Address Automatically” and “Obtain DNS Address Automatically”. Try to log into the
modem’s web interface by typing 192.168.254.254 in your browser.
Login as....
Username: admin
Password: admin
Go to “Settings”.
Choose “Restore Default”
The modem will reboot.
Done. You now have admin access to your modem.
pag ayaw mag hardreset po kayo ulitin nyo :p
WALANG KWENTA ADMIN!! Kulang TABs!! parang User lang And DAMOT ni Globe!! walang APN setting
Dahil Walang kwenta yung admin mag CID Reader nalang tayo wahaha or Mobile Partner pwede din mag set ng APN or 3G Only parasa RED LIGHT na SMART sakit ni 315s 4G REDLIGHT....
Set the APN to “internet.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Postpaid/LTE)
Enter this command:
AT+CGDCONT=1,"IP","internet.globe.com.ph"
OR Set the APN to “http.globe.com.ph” of the Globe Network to be connected to (use if sim is Globe Prepaid/LTE)
Enter this command:
AT+CGDCONT=1,"IP","http.globe.com.ph”
OR Set the APN to “internet” of the Smart Network to be connected to (use if sim is Smart Prepaid/LTE).
Enter this command:
AT+CGDCONT=1,"IP","internet”
Last command Reboots the modem.
AT^reset
Eto ibig sabihin ng format ng command
AT+CGDCONT=1,"IP","http.globe.com.ph"
ATD*99***1#
red = profile priority
green = IP address ex:format (xx.xx.xx.xx)
blue = APN name
pink = dialup number (optional kung 3g ang masagap na signal) source (Freddy3k)
MOBILE PARTNER USB MODE
No Signal if naka Lock sa LTE Only
Gawin mo AUTO yan mag kakasignal na yan
Paano Gawin Pumunta sa Setting Preferences
UPDATE FULL ADMIN DE-BRAND
Pag nasa Step 4 kayo sa itaas pwede nyo diretso debrand na yan
Procedure ay galing dito http://www.symbianize.com/showthread.php?t=1341870
Post a Comment